![will lathe and plaster walls hold shelf will lathe and plaster walls hold shelf](https://empire-s3-production.bobvila.com/articles/wp-content/uploads/2019/02/Lath_and_Plaster.jpg)
Thanks for that Apart from a box room and a wee bathroom adding some inches to the exterior walls shouldn't be a problem in most rooms, though as you say it will be a lot of work: there will be a fair bit of stuff like cornices, architraves & fire surrounds to replace/move. If rooms are big enough you don,t even need to rip out old plaster +lathes-just build a modern house inside it inside it ?Īpply vapour barrier to the frames before you lift them up into place and you got full damp proofing at same time and a gap for the old walls to breath into the roof spaceĪ house that old will be built with a cold roof and lots of drafts in the loft area -so you kill all problems at same timeĪlso will be a job you can do while still living in it ,a bit at a time if you wishįilling the gap with anything will stop the air flow to the roof you must have with this type of old house -you will make more damp problems Many renovators and owners of older properties will discover lath and plaster ceilings when they come to remodel and decorate their homes. Maybe a bigger job then you wanted but is the right way to go long term and also a chance to replace electrics etc at same time and have house with modern insulation stds Lath and plaster ceilings and walls were common in houses built from the 1700s right up until the early 1900s. Make sure the screws are smaller than the shelf so you don’t screw through the surface.Maybe time to think about getting rid of the lathe and plaster and build stud walls -providing rooms are not very small Screw and tighten the shelves to the bracket using wood screws to ensure its safe position. Usually, there are holes on the bottom of the shelves.
![will lathe and plaster walls hold shelf will lathe and plaster walls hold shelf](https://i.pinimg.com/originals/af/ab/b8/afabb862f2987f6c8f4d5a698489b409.png)
Make sure to use appropriate hardware for the size of the. If no studs are available, you can use wall anchors and toggle bolts to securely mount the shelf. When attaching shelves to plaster walls, it is important to screw the shelves into a stud in the wall. Make adjustments until you achieve the desired effect. Plaster walls are strong and can easily hold a shelf or wall-mounted shelving system. Place the level above the plank to ensure it’s perfectly vertical. Once the brackets are installed on the wall, slide the shelf through the bracket tubes. Use a level to make sure the brackets are vertical and screw the wood nails until they’re fixed safely and securely. If that’s not the case, consult with the manufacturer to recommend the best brackets for floating shelves. Usually, the wall brackets come in the shelving packaging. After that, tighten the goggle on the wall. To install the wall goggles, first drill a pilot hole as well. If you’re not drilling on the wall studs, first install wall goggles to screw the screws in them. This will guarantee the shelves are tight on the wall. Next, use a slightly bigger drill bit, but make sure it’s still a bit smaller than the screws of the brackets. This will prevent the plaster from cracking and will make the drilling of the larger holes easier. As the laths are very flexible they allow the wall to move, and as the plaster has degraded it often crumbles behind and in between the laths. Step 4: Drill holesįirst, drill pilot holes through the plaster on the marked positions by using the smallest drill bit you can find. Use a pencil and mark the holes where you’ll be drilling to mount the brackets on the wall. Use a level and adjust the position of the bracket until it’s perfectly vertical. Place the bracket against the wall at the location where the shelves would be installed. Plan to position the brackets over the centre of the studs for extra security. Be sure to mark both the studs’ edges and the exact place where you’ll be drilling. Once you have defined the exact position of the wall studs, decide on what height and the weight you want your shelves to be. Make sure they’re wider enough to anchor both of the ends on the wall studs. If you plan to have more storage space, choose longer ones. If you plan them to hold heavier items, you should choose thicker shelves. How to install floating shelves Step 1: Choose the right shelves typeĭetermine what you’ll use the shelves for. This will prevent the plaster from mashing up too much.
![will lathe and plaster walls hold shelf will lathe and plaster walls hold shelf](https://www.thegrumble.com/proxy.php?image=https:%2F%2Fi.imgur.com%2F4p75I0t.jpg)
Tighten the screws in them when mounting the shelves. To do so, you need to pre-drill wall toggles through the plasterboard. You might need a helping hand for this step. Use the level and mark the location with your pencil on top and on the sides of your shelf. Now that you have located your wall studs, set the spot for your shelf on the wall. Pro tip: If you can’t find the wall studs or the shelves you want to install are smaller and both the ends can’t be located on a wall stud, you can still install the shelving on your desired position. Mark the location of wall studs onto the plaster with your pencil.